Ss-cycle USB Magneti Marelli Style VFI (Variable Fuel Injec Manuel d'utilisateur télécharger pdf

S&S

Cycle, Inc.

14025 Cty Hwy G, PO Box 215

Viola, Wisconsin 54664

Phone: 608-627-1497 • Fax: 608-627-1488

Technical Service Phone: 608-627-TECH (8324)

Technical Service Email: [email protected]om

Website: www.sscycle.com

Installation Instructions for S&S USB Magneti Marelli® Style VFI

(Variable Fuel Injection) Module and ProTune II Software

IMPORTANT NOTICE:

Statements in this instruction sheet preceded by the following words are of

special signicance.

WARNING

Means there is the possibility of injury to yourself or others.

CAUTION

Means there is the possibility of damage to the part or motorcycle.

NOTE

Other information of particular importance has been placed in italic type.

S&S recommends you take special notice of these items.

WARRANTY:

All S&S parts are guaranteed to the original purchaser to be free of

manufacturing defects in materials and workmanship for a period of twelve

(12) months from the date of purchase. Merchandise that fails to conform to

these conditions will be repaired or replaced at S&S’s option if the parts are

returned to us by the purchaser within the 12 month warranty period or within

10 days thereafter.

In the event warranty service is required, the original purchaser must call or

write S&S immediately with the problem. Some problems can be rectied by

a telephone call and need no further course of action.

A part that is suspect of being defective must not be replaced by a Dealer

without prior authorization from S&S. If it is deemed necessary for S&S to

make an evaluation to determine whether the part was defective, a return

authorization number must be obtained from S&S. The parts must be packaged

properly so as to not cause further damage and be returned prepaid to S&S

with a copy of the original invoice of purchase and a detailed letter outlining

the nature of the problem, how the part was used and the circumstances at

the time of failure. If after an evaluation has been made by S&S and the part

was found to be defective, repair, replacement or refund will be granted.

ADDITIONAL WARRANTY PROVISIONS:

(1) S&S shall have no obligation in the event an S&S part is modied by any

other person or organization.

(2) S&S shall have no obligation if an S&S part becomes defective in whole or in

part as a result of improper installation, improper maintenance, improper use,

abnormal operation, or any other misuse or mistreatment of the S&S part.

(3) S&S shall not be liable for any consequential or incidental damages

resulting from the failure of an S&S part, the breach of any warranties, the

failure to deliver, delay in delivery, delivery in non-conforming condition, or

for any other breach of contract or duty between S&S and a customer.

(4) S&S parts are designed exclusively for use in Harley-Davidson® and other

American v-twin motorcycles. S&S shall have no warranty or liability obligation

if an S&S part is used in any other application.

SAFE INSTALLATION AND OPERATION RULES:

Before installing your new S&S part it is your responsibility to read and follow

the installation and maintenance procedures in these instructions and follow

the basic rules below for your personal safety.

Gasoline is extremely ammable and explosive under certain conditions •

and toxic when breathed. Do not smoke. Perform installation in a well

ventilated area away from open ames or sparks.

If motorcycle has been running, wait until engine and exhaust pipes •

have cooled down to avoid getting burned before performing any

installation steps.

Before performing any installation steps disconnect battery to eliminate •

potential sparks and inadvertent engagement of starter while working

on electrical components.

Read instructions thoroughly and carefully so all procedures are •

completely understood before performing any installation steps.

Contact S&S with any questions you may have if any steps are unclear or

any abnormalities occur during installation or operation of motorcycle

with a S&S part on it.

Consult an appropriate service manual for your motorcycle for correct •

disassembly and reassembly procedures for any parts that need to be

removed to facilitate installation.

Use good judgment when performing installation and operating •

motorcycle. Good judgment begins with a clear head. Don’t let

alcohol, drugs or fatigue impair your judgment. Start installation

when you are fresh.

Be sure all federal, state and local laws are obeyed with the installation. •

For optimum performance and safety and to minimize potential •

damage to carb or other components, use all mounting hardware that is

provided and follow all installation instructions.

Motorcycle exhaust fumes are toxic and poisonous and must not be •

breathed. Run motorcycle in a well ventilated area where fumes can

dissipate.

DISCLAIMER:

S&S parts are designed for high performance, closed course, racing

applications and are intended for the very experienced rider only. The

installation of S&S parts may void or adversely aect your factory warranty.

In addition such installation and use may violate certain federal, state, and

local laws, rules and ordinances as well as other laws when used on motor

vehicles used on public highways, especially in states where pollution laws

may apply. Always check federal, state, and local laws before modifying your

motorcycle. It is the sole and exclusive responsibility of the user to determine

the suitability of the product for his or her use, and the user shall assume all

legal, personal injury risk and liability and all other obligations, duties, and

risks associated therewith.

The words Harley®, Harley-Davidson®, H-D®, Sportster®, Evolution®, and all

H-D part numbers and model designations are used in reference only. S&S

Cycle is not associated with Harley-Davidson, Inc.

Instruction 510-0009

10-20-10

by S&S® Cycle, Inc.

Printed in the U.S.A.

1 2 3 4 5 6 ... 11 12

Cycle, Inc 1

Résumé du contenu

Page 1 - Cycle, Inc

S&S® Cycle, Inc.14025 Cty Hwy G, PO Box 215 Viola, Wisconsin 54664Phone: 608-627-1497 • Fax: 608-627-1488Technical Service Phone: 608-627-TE

Page 2

10BASIC TROUBLESHOOTING1- Problem: ProTune II is not communicating with the VFI module.a- Check that the VFI module is powered. The VFI module must

Page 3

11STOCK THROTTLE BODY SETUP PROCEDURES&S calibrations for use with stock Magneti Marelli® dual bore throttle bodies are setup to use the factory

Page 4

123- Base Hot and Cold Idle Screw Settings for 1550cc (95”)a- Apply a small amount of blue Loctite® to the cold idle screw. Install the screw and ad

Page 5

2NOTE: All brand names, trademarks or registered trademarks mentioned in these instructions are the property of their respective holders and are used

Page 6

3ADDITIONAL PARTS REqUIREDIn most instances, the VFI module will be pre-programmed. If the VFI module included in this kit has not been programmed, th

Page 7

4If you are new to the ProTune II program, you should load it on a computer and familiarize yourself with the screen and the controls before connectin

Page 8

5g- ProTune II will now install and copy les to your computer. If a warning message appears during driver installation click Install/Continue Anyway

Page 9

6Installing USB DriversNOTE: The rst time the VFI module is connected to a PC, the USB drivers will need to be installed for ProTune II to communicat

Page 10

7c- Windows will locate the correct driver le and copy the required les. Wait for this to complete.d- Depending on your security settings, a warni

Page 11

8c- Depending on your user account settings a security warning message may appear asking you to conrm the device installation. Allow the installatio

Page 12

9Loading a CalibrationIn most instances, the VFI module will be pre-programmed. If the module included in this kit has not been programmed, this will

Commentaires sur ces manuels

Pas de commentaire

Ss-cycle USB Magneti Marelli Style VFI (Variable Fuel Injec Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Ss-cycle USB Magneti Marelli Style VFI (Variable Fuel Injec. S&S Cycle USB Magneti Marelli Style VFI (Variable Fuel Injection) Module and ProTune II Software User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Ss-cycle USB Magneti Marelli Style VFI (Variable Fuel Injec