Ss-cycle Torque Plate Kit for 4 1/8 Bore Cylinders Manuel d'utilisateur télécharger pdf

S&S

Cycle, Inc.

235 Causeway Blvd.

La Crosse, Wisconsin 54603

Phone: 608-627-1497 • Fax: 608-627-1488

Technical Service Phone: 608-627-TECH (8324)

Technical Service Email: [email protected]

Website: www.sscycle.com

Because every industry has a leader

SAFE INSTALLATION AND OPERATION RULES:

Before installing your new S&S part it is your responsibility to read and

follow the installation and maintenance procedures in these

instructions and follow the basic rules below for your personal safety.

● Gasoline is extremely flammable and explosive under certain

conditions and toxic when breathed. Do not smoke. Perform

installation in a well ventilated area away from open flames or spar

ks.

● If motorcycle has been running, wait until engine and exhaust pipes

have cooled down to avoid getting burned before pe

rforming any

installation steps.

● Before performing any installation steps disconnect battery to

eliminate potential sparks and inadvertent engagement of star

ter while

working on electrical components.

● Read instructions thoroughly and carefully so all pr

ocedures are

completely understood before performing any installation steps.

Contact S&S with any questions you may have if any steps are unclear

or any abnormalities occur during installation or operation of

motorcycle with a S&S part on it.

● Consult an appropriate service manual for your motorcycle for correct

disassembly and reassembly procedur

es for any parts that need to be

removed to facilitate installation.

● Use good judgement when performing installation and operating

motorcycle. Good judgement begins with a clear head. Don't let

alcohol, drugs or fatigue impair your judgement. Start installation

when you are fresh.

● Be sure all federal, state and local laws ar

e obeyed with the

installation.

● For optimum performance and safety and to minimize potential

damage to carb or other components, use all mounting hardwar

e that

is provided and follow all installation instructions.

● Motorcycle exhaust fumes are toxic and poisonous and must not

be breathed. Run motorcycle in a well ventilated area wher

e fumes

can dissipate.

DISCLAIMER:

S&S parts are designed for high performance, off road, racing

applications and are intended for the very experienced rider only. The

installation of S&S parts may void or adversely effect your factory

warranty. In addition such installation and use may violate certain

federal, state, and local laws, rules and ordinances as well as other laws

when used on motor vehicles used on public highways, especially in

states where pollution laws may apply. Always check federal, state, and

local laws before modifying your motorcycle. It is the sole and exclusive

responsibility of the user to determine the suitability of the product for

his or her use, and the user shall assume all legal, personal injury risk and

liability and all other obligations, duties, and risks associated therewith.

The words Harley

, Harley-Davidson

, H-D

, Sportster

, Evolution

, and

all H-D part numbers and model designations are used in reference only.

S&S Cycle is not associated with Harley-Davidson, Inc.

IMPORTANT NOTICE:

Statements in this instruction sheet preceded by the following words

are of special significance.

WARNING

Means ther

e is the possibility of injury to yourself or others.

CAUTION

Means there is the possibility of damage to the part or motorcycle.

NOTE

Other information of particular importance has been placed in italic type.

S&S recommends you take special notice of these items.

WARRANTY:

All S&S parts are guaranteed to the original purchaser to be free of

manufacturing defects in materials and workmanship for a period of

twelve (12) months from the date of purchase. Merchandise that fails

to conform to these conditions will be repaired or replaced at S&S’s

option if the parts are returned to us by the purchaser within the 12

month warranty period or within 10 days thereafter.

In the event warranty service is required, the original purchaser must

call or write S&S immediately with the problem. Some problems can be

rectified by a telephone call and need no further course of action.

A part that is suspect of being defective must not be replaced by a

Dealer without prior authorization from S&S. If it is deemed necessary

for S&S to make an evaluation to determine whether the part was

defective, a return authorization number must be obtained from S&S.

The parts must be packaged properly so as to not cause further damage

and be returned prepaid to S&S with a copy of the original invoice of

purchase and a detailed letter outlining the nature of the problem,

how the part was used and the circumstances at the time of failure. If

after an evaluation has been made by S&S and the part was found to

be defective, repair, replacement or refund will be granted.

ADDITIONAL WARRANTY PROVISIONS:

(1) S&S shall have no obligation in the event an S&S part is modified by

any other person or organization.

(2) S&S shall have no obligation if an S&S part becomes defective in

whole or in part as a result of improper installation, improper

maintenance, improper use, abnormal operation, or any other misuse

or mistreatment of the S&S part.

(3) S&S shall not be liable for any consequential or incidental damages

resulting from the failure of an S&S part, the breach of any

warranties,the failure to deliver, delay in delivery, delivery in non-

conforming condition, or for any other breach of contract or duty

between S&S and a customer.

(4) S&S parts are designed exclusively for use in Harley-Davidson and

other American v-twin motorcycles. S&S shall have no warranty or

liability obligation if an S&S part is used in any other application.

Installation Instructions: S&S

Torque Plate Kit

for 4

⁄8” Bore Cylinders

Instruction 51-1172

5-3-06

2003, 2005, 2006

by S&S Cycle, Inc.

Printed in the U.S.A.

The plates in this kit should only be used for honing S&S 4

⁄8” bore cylinders.

1 2 3 4

Cycle, Inc 1

Résumé du contenu

Page 1 - Cycle, Inc

S&S®Cycle, Inc.235 Causeway Blvd.La Crosse, Wisconsin 54603Phone: 608-627-1497 • Fax: 608-627-1488Technical Service Phone: 608-627-TECH (832

Page 2

INTRODUCTIONS&S®cylinder torque plates simulate the stress cylinders experience when installed on an engine during honing operations. Acylinder th

Page 3

3- Apply light coat of 20W50 motor oil to threads and underside of heads of the four provided 7⁄16"-20 x 6" socket head bolts.4- Insert the

Page 4

Because every industry has a leader

Commentaires sur ces manuels

Pas de commentaire

Ss-cycle Torque Plate Kit for 4 1/8 Bore Cylinders Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Ss-cycle Torque Plate Kit for 4 1/8 Bore Cylinders. S&S Cycle Torque Plate Kit for 4 1/8 Bore Cylinders User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Ss-cycle Torque Plate Kit for 4 1/8 Bore Cylinders