Ss-cycle Non-Copper Head Gaskets for Harley-Davidson Evolut Manuel d'utilisateur télécharger pdf

S&S

Cycle, Inc.

14025 Cty Hwy G PO Box 215

Viola, Wisconsin 54664

Phone: 608-627-1497 • Fax: 608-627-1488

Technical Service Phone: 608-627-TECH (8324)

Technical Service Email: sstech@sscycle.com

Website: www.sscycle.com

Installation Instructions: S&S® Non-Copper Head Gaskets

for Harley-Davidson® Evolution® & Twin Cam 88® Engines

Instruction 51-1016

04-08-13

by S&S® Cycle, Inc.

Printed in the U.S.A.

NOTE: Cleaning parts prior to and during

assembly and keeping parts clean after nal

assembly are imperative to minimize con-

taminants that may circulate in oil and shorten

engine life. Many parts can be cleaned with soap

and water rst. Then, reclean all internal parts

and gasket mating surfaces using high quality

solvent that does not leave any harmful resi-

dues. Be sure to read and follow manufacturer’s

instruction label before use. Use brushes and

compressed air to clean all oil passageways of

dirt, lings, etc. whenever possible. During nal

assembly, recoat all internal parts with clean

motor oil.

CAUTION

Installer is responsible for ensuring parts

are clean at assembly. Damage caused by

manufacturing chips, dirt and/or other con-

taminants is not covered under warranty.

WARNING

• Some solvents, degreasers and other

chemicals are harmful. Many items are

ammable and present a re hazard.

Read the manufacturer’s instruction label

for proper use. Use in well ventilated area

and wear protective clothing to avoid in-

jury.

• Compressed air and particles dislodged

by compressed air are harmful to eyes

and body. Wear protective goggles when

using compressed air and always direct

air stream away from body parts such as

hands and eyes. Never direct compressed

air toward other people.

Top End Assembly Procedure

A. Thoroughly clean all top end parts and

blow dry with compressed air. Use high

grade lacquer thinner on gasket surfaces.

B. Install base gaskets dry. Be sure gaskets

match cylinder base line up dowels and oil

return passageways.

C. Install pistons and rings per instructions, or

S&S® piston instruction sheet 51-1028.

D. Coat piston skirts with engine oil and

install cylinders.

E. Install head gaskets dry with widest

side of metal re ring against cylinder.

NOTE: S&S 3¾" bore head gaskets for 1999-up

big twins require o-rings around the cylinder

head locating dowels similar to stock head

gaskets. S&S 3⁄", 4" and 4⁄" bore head gaskets

do not use o-rings around cylinder head locating

dowels.

NOTE: All S&S cylinder head kits are supplied

with .045" thick head gaskets. This clearance

promotes better combustion chamber

turbulence and ame travel.

CAUTION

Insucient clearance between piston

domes and cylinder heads or piston domes

and valves will cause damage to pistons,

heads and/or valves.

F. Before installing heads, check the threads of

cylinder studs and head bolts by spinning

each head bolt down on its respective

stud to be sure threads are clean and

undamaged. If binding is encountered,

correct before proceeding. Place a drop or

two of oil on threads of each head bolt just

prior to nal assembly.

1 2

Cycle, Inc 1

Résumé du contenu

Page 1 - Cycle, Inc

S&S® Cycle, Inc.14025 Cty Hwy G PO Box 215Viola, Wisconsin 54664Phone: 608-627-1497 • Fax: 608-627-1488Technical Service Phone: 608-627-TECH (83

Page 2

NOTE: Light coating of oil on head bolt threads minimizes friction so torque values will not be distorted. It cannot be emphasized enough how importan

Commentaires sur ces manuels

Pas de commentaire

Ss-cycle Non-Copper Head Gaskets for Harley-Davidson Evolut Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Ss-cycle Non-Copper Head Gaskets for Harley-Davidson Evolut. S&S Cycle Non-Copper Head Gaskets for Harley-Davidson Evolution & Twin Cam 88 Engines User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Ss-cycle Non-Copper Head Gaskets for Harley-Davidson Evolut