Ss-cycle Super Stock C Ignition in Carbureted, 2004–2007 Am Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Ss-cycle Super Stock C Ignition in Carbureted, 2004–2007 Am. S&S Cycle Super Stock C Ignition in Carbureted, 2004–2007 American Ironhorse Motorcycles User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 6
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
S&S
®
Cycle, Inc.
14025 Cty Hwy G PO Box 215
Viola, Wisconsin 54664
Phone: 608-627-1497 Fax: 608-627-1488
Technical Service Phone: 608-627-TECH (8324)
Technical Service Email: sstech@sscycle.com
Website: www.sscycle.com
Installation Instructions: S&S® Super Stock® C Ignition
in Carbureted, 20042007 American Ironhorse® Motorcycles
IMPORTANT NOTICE:
Statements in this instruction sheet preceded by the following words are
of special signicance.
WARNING
Means there is the possibility of injury to yourself or others.
CAUTION
Means there is the possibility of damage to the part or motorcycle.
NOTE:
Other information of particular importance has been placed in italic type.
S&S recommends you take special notice of these items.
WARRANTY:
All S&S parts are guaranteed to the original purchaser to be free of
manufacturing defects in materials and workmanship for a period of twelve
(12) months from the date of purchase. Merchandise that fails to conform to
these conditions will be repaired or replaced at S&S’s option if the parts are
returned to us by the purchaser within the 12 month warranty period or within
10 days thereafter.
In the event warranty service is required, the original purchaser must call or
write S&S immediately with the problem. Some problems can be rectied by a
telephone call and need no further course of action.
A part that is suspect of being defective must not be replaced by a Dealer
without prior authorization from S&S. If it is deemed necessary for S&S to
make an evaluation to determine whether the part was defective, a return
authorization number must be obtained from S&S. The parts must be packaged
properly so as to not cause further damage and be returned prepaid to S&S
with a copy of the original invoice of purchase and a detailed letter outlining
the nature of the problem, how the part was used and the circumstances at
the time of failure. If after an evaluation has been made by S&S and the part
was found to be defective, repair, replacement or refund will be granted.
ADDITIONAL WARRANTY PROVISIONS:
(1) S&S shall have no obligation in the event an S&S part is modied by any
other person or organization.
(2) S&S shall have no obligation if an S&S part becomes defective in whole or in
part as a result of improper installation, improper maintenance, improper use,
abnormal operation, or any other misuse or mistreatment of the S&S part.
(3) S&S shall not be liable for any consequential or incidental damages
resulting from the failure of an S&S part, the breach of any warranties, the
failure to deliver, delay in delivery, delivery in non-conforming condition, or
for any other breach of contract or duty between S&S and a customer.
(4) S&S parts are designed exclusively for use in Harley-Davidson® and other
American v-twin motorcycles. S&S shall have no warranty or liability obligation
if an S&S part is used in any other application.
SAFE INSTALLATION AND OPERATION RULES:
Before installing your new S&S part it is your responsibility to read and
follow the installation and maintenance procedures in these instructions
and follow the basic rules below for your personal safety.
Gasoline is extremely ammable and explosive under certain conditions
and toxic when breathed. Do not smoke. Perform installation in a well
ventilated area away from open ames or sparks.
If motorcycle has been running, wait until engine and exhaust pipes have
cooled down to avoid getting burned before performing any installation
steps.
Before performing any installation steps disconnect battery to eliminate
potential sparks and inadvertent engagement of starter while working
on electrical components.
Read instructions thoroughly and carefully so all procedures are
completely understood before performing any installation steps.
Contact S&S with any questions you may have if any steps are unclear or
any abnormalities occur during installation or operation of motorcycle
with a S&S part on it.
Consult an appropriate service manual for your motorcycle for correct
disassembly and reassembly procedures for any parts that need to be
removed to facilitate installation.
Use good judgment when performing installation and operating
motorcycle. Good judgment begins with a clear head. Don’t let alcohol,
drugs or fatigue impair your judgment. Start installation when you are
fresh.
Be sure all federal, state and local laws are obeyed with the installation.
For optimum performance and safety and to minimize potential damage
to carb or other components, use all mounting hardware that is provided
and follow all installation instructions.
Motorcycle exhaust fumes are toxic and poisonous and must not be
breathed. Run motorcycle in a well ventilated area where fumes can
dissipate.
DISCLAIMER:
S&S parts are designed for high performance, closed course, racing
applications and are intended for the very experienced rider only. The
installation of S&S parts may void or adversely aect your factory warranty.
In addition such installation and use may violate certain federal, state, and
local laws, rules and ordinances as well as other laws when used on motor
vehicles used on public highways, especially in states where pollution laws
may apply. Always check federal, state, and local laws before modifying
your motorcycle. It is the sole and exclusive responsibility of the user to
determine the suitability of the product for his or her use, and the user shall
assume all legal, personal injury risk and liability and all other obligations,
duties, and risks associated therewith.
All brand names, trademarks, or registered trademarks mentioned in these
instructions are the property of their respective holders and are used in a
reference only capacity.
The words Harley®, Harley-Davidson®, H-, Sportster®, Evolution®, and all
H-D part numbers and model designations are used in reference only. S&S
Cycle is not associated with Harley-Davidson, Inc.
Instruction 510-0035
05-16 -11
Copyright © 2011
by S&S® Cycle, Inc.
All rights reserved.
Printed in the U.S.A.
Vue de la page 0
1 2 3 4 5 6

Résumé du contenu

Page 1 - Cycle, Inc

S&S® Cycle, Inc.14025 Cty Hwy G PO Box 215Viola, Wisconsin 54664Phone: 608-627-1497 • Fax: 608-627-1488Technical Service Phone: 608-627-TECH (83

Page 2

2A. Introduction The S&S Super Stock® C is a reliable replacement for the stock ignition module found on 2004–2007 American IronHorse® Motorcycl

Page 3 - Figure 1

32004 American IronHorse® Super Stock® C Ignition Wiring DiagramFigure 1Super Stock® - C Ignition ModuleS&S Cycle, Inc.LaCrosse, WI 54603www.ssc

Page 4

4American IronHorse® 2005–2007 Model Installation 1. Be sure that ignition switch is o and disconnect battery. 2. Remove stock ignition module 3

Page 5 - Figure 2

52005–2007 American IronHorse® Super Stock® C Ignition Wiring DiagramFigure 2Super Stock® - C Ignition ModuleS&S Cycle, Inc.LaCrosse, WI 54603ww

Commentaires sur ces manuels

Pas de commentaire